ZEKOO 12 FT Bypass Sliding Barn Door Hardware Kit - Single Track System for Double Wooden Doors - One-Piece Rail Flat Track Roller with Spoke Wheel Style - Perfect for Farmhouse, Rustic, and Modern Home Decor (12 Feet)

ZEKOO has devoted to the development of barn door hardware over 10 years, improve and upgrade products to give each family the most appropriate choice ZEKOO 12ft single track bypass sliding barn door hardware kit use for double doors (door is not include) Q: How to choose barn door track size of single track bypass system? A: Barn door track length = Your opening width +1FT. For example, if your opening is 11FT (132'') wide, you will need 11T+1FT = 12 FT（144''） long track, your each door needs to be 72'' wide, your opening will show 67'' wide when the door open. Q: Can the single track bypass barn door hardware system let the opening show fully? A: Yes, you can select a longer track, if each door is 72'' wide, you can choose 18 FT track kit, if you need it, please let us know. Q: How confirm door width for the single track bypass system? A: Because this is single track bypass, one track hang 2 doors, the wheel diameter is 4-3/4'' , so there are at least have 10'' overlap between 2 doors, so your each door width = Half width of opening + 6'' Q: Can each door slide independently on the track? A: No, the 2 doors slide on same track, so the 2 rollers will be hit together when one door slide to the end, maybe drive another door slide, if you have enough ceiling space above door for 13'', you can choice double track bypass system, please search ASIN number B06Y1M4MP3 from our shop Q: Can the single track bypass use for four door also? A: Yes, you can add 1 set straight hanger B088N7N7NC and 1 set offset hanger B09DSW5GH9 for the other 2 doors, please search the product number from our shop, just need to know that there have 10'' overlap between 2 doors, so each door need add 6'' wider About all accessories of 12 FT single track bypass hardware Track: 2 piece whole 6ft rail, Pre-drilled 16" apart holes on track, make by solid 1/4" (6.3mm) thick steel, with 8.8 grade high strength bearing capacity lag blots, fit for concrete wall and wooden wall Track spacer: Provide 1-3/8'' length spacer, it can control the gap between the door and the wall, if you have the door trim on wall, you can change other length spacer, please tell us Door stopper: Prevent the door falling off from the track, it installed at the end of track 2 side, ensure the stability and safety, with the rubber plug, good damping effect and reduce the noise, have 2 screws to fasten stopper on track, you can put stopper on track where you want to stop your door, easy to remove if you want adjust Floor guide: can prevent the door swinging back and forth or against the baseboard, let your door slide on same locus, fit for all thickness with grooved or ungrooved doors Anti-jumper: can prevent door to be lifted off rail when the barn door slide, ensure the stability and safety The barn door hanger roller with Professional bearings, make your bypass barn door hardware service life last longer About the bearing Material quality is high purity bearing steel Gcr15, professional bearing materials, ring fixed structure bearing, wraps around the steel ball and prevent steel ball from leaving the locus, make sliding more stable.There is a dust cover the bearing to prevent dust from entering and lubricating oil leakage, let the roller can slide smoothly and more durable.1 hanger with 2 life time lubricated bearing, ensure sliding balance and stability, test beyond 160,000, you can use it for a long time. About the hanger The roller surface is covered with nylon, wear-resisting and slide very quietly.We design the Dowel pin Front part slightly larger, keep the dowel stuck in hole not fall off.All of prat is make by Q235 carbon steel, thick is 1/4'' (6.3mm)8.8 grade roller bolt can hold the doors comfortablyThe offset hanger with anti-jump design, give you safe sliding door experience Single track bypass hardware kit package include 2 x 6 FT Rail 1 x Junction plate 2 x Straight steel Hanger with bolt 2 x Offset steel Hanger with bolt 2 x Door Stopper with Hex Wrench 10 x 1-3/8'' Spacer with lag bolt 2 x Floor Guide with screw 2 x Anti-Jumper with screw 2 x Offset Anti-Jumper with screw 1 x Barn Door Hardware Installation Manual Why choice Single track bypass barn door hardware Single track bypass barn door hardware system slides horizontally, it can save space compared with ordinary push doorWall-mounted is low ceiling 8'' install, no tedious installation steps, no request wall to be twice the width of the opening, suitable for small home spaceDecorate your locker room, closet, kitchen, wardrobe, bathroom, bedroom, storeroom, change your home dull image Barn door Installation dimension Q: How much gap of the double track bypass system? A: We suggest door thickness less than or equal to 1-9/16'', If your door thickness is 1-9/16'', the gap between inner door&wall is about 5/8'' , the gap between two door panels is about 1-3/16'' , the outer door extend from the wall is 5''. Q: How to narrow the gap for the thinner door? A: If the thinner the door, the larger the gap, you can add a headboard on front of door, then install the hanger on headboard, that can narrow the gap of door with wall and door with door. Single track barn door bypass instructions step by step with fractional measurements in inch, have detailed word instructions with pictures Installation dimension The track drilling hole on wall is = your door height + 1-11/16''The hanger first hole install on door is 1-9/16” from top of door, second hole is 3-9/16” from first hole Q: How much ceiling space requirement of the single track bypass system？ A: At least 8" from top of door to ceiling to install. Q: Can i cut the track? A: Yes, you can cut it into any length of you want Q: Can i use it for outdoors ? A: We suggest if use for outdoors, you can make some cover above the track, and you need paint and add oil regularly to extended service life Q: What circumstances do I need to add a headboard? A: 1. If you have a doorway trim; 2. If the studs don't line up with the pre-drilled holes in the rail Q: How thick door use for it? What is the weight capacity? A: 1. We suggest 1-3/8" ~ 1-9/16" thick door will be better, If your door thick is 1-1-3/4", the inner door bolts need reverse installation, because the offset hanger size is fixed; 2. Track limited 230lbs. 2 side handle for the single track bypass barn door floor guide I Single track bypass J Single track bypass Double track bypass Buying Options Buying Options Buying Options Buying Options Add to Cart Customer Reviews 4.8 out of 5 stars 265 4.5 out of 5 stars 677 4.4 out of 5 stars 1,911 4.6 out of 5 stars 1,075 4.3 out of 5 stars 550 Price $16.32$16.32 $9.99$9.99 $72.24$72.24 — no data $149.99$149.99 Use For Better for the bypass kit no data 2 doors 2 doors Independent sliding system